Time left:

UPPCL Date: 08_09_2021 Shift: S2


Q.1In electrodynamometer movement, the deflection of the pointer is:
A. inversely proportional to the current squared
B. directly proportional to the current
C. directly proportional to the current squared
D. inversely proportional to the current
Q.2What is the unit of measurement for slew rate of an op-amp?
A. nA
B. V/µs
C. Ampere
D. dB
Q.3In a 6-pole DC machine, 45 mechanical degrees corresponds to __________________ electrical degrees.
A. 180
B. 90
C. 135
D. 45
Q.4Boiler efficiency can be improved by _______________ due to economiser.
A. 1 to 2 percent
B. 4 to 10 percent
C. 12 to 15 percent
D. 20 percent
Q.5In power transmission line, which phenomenon causes the ionisation of the air surrounding the power conductor?
A. Corona
B. Ferranti effect
C. Flashing
D. Skin effect
Q.6निम्न में से कौन-सा किसी संगठन में नौकरी शीर्षक और एक दूसरे के लिए उनके संबंधों को दर्शाता है?
A. मानक अभ्यास निर्देश (Standard practice instructions)
B. संगठन चार्ट (Organisation chart)
C. संगठन की नियम पुस्तिका (Organisation rule book)
D. संगठन मैनुअल (Organisation manual)
Q.7The effective length of a short transmission line is less than _______________.
A. 80 km
B. 100 km
C. 160 km
D. 320 km
Q.8Normally, overhauling is performed at an interval of _______.
A. 1 week
B. 1 month
C. 5 years
D. 6 months
Q.9As compared to an incandescent lamp, CFL offers approximately _________ savings in electricity costs.
A. 5 to 10 percent
B. 20 to 30 percent
C. 40 to 50 percent
D. 70 to 80 percent
Q.10An atom of hydrogen has ___________________ in its first orbit.
A. 8 electrons
B. 2 electrons
C. 4 electrons
D. 1 electron
Q.11Which of the following is NOT a valid characteristics of switched mode power supply as compared to linear power supply?
A. Smaller size of transformer
B. Light weight
C. Higher efficiency
D. Low noise at output
Q.12In which of the following methods of welding is a transducer used to convert high frequency electric power into vibratory energy?
A. DC arc welding
B. Resistance welding
C. Ultrasonic welding
D. MIG welding
Q.13The real part of the propagation constant of a transmission line is:
A. phase constant
B. stability constant
C. reliability factor
D. attenuation constant
Q.14An op-amp based integrator converts the DC level into a ________ output.
A. linearly increasing ramp
B. saw-tooth
C. triangular
D. square wave
Q.15
A.
B.
C.
D.
Q.16The wave used to minimise heat dissipation in the switching transistor of an SMPS is a:
A. square wave
B. sine wave
C. triangular wave
D. saw-tooth wave
Q.17What is the aim of all energy conservation techniques?
A. To experiment with new energy sources
B. To promote non-renewable energy sources
C. To replace old equipment with new ones
D. To reduce energy losses
Q.18Which of the following statements is INCORRECT for HVDC transmission?
A. Charging current is absent.
B. It suffers from skin effect.
C. Corona losses are less as compared to a.c. transmission.
D. It operates at unity power factor.
Q.19Which of the following is an alloy of aluminium?
A. Hindalium
B. Brass
C. German silver
D. Monel metal
Q.20Because of corona, in case of AC transmission, _________ harmonics are always present.
A. 11th
B. 7th
C. 3rd
D. 5th
Q.21Which of the following gates is also called universal gate?
A. NOT
B. AND
C. NOR
D. EX-OR
Q.22In case of ETAP software, the full form of ETAP is:
A. Estimation of Transient Analysis of Power
B. Electrical Transient Analyzer Program
C. Electrical Transformer Analysis Program
D. Electrical Testing and Analysis Program
Q.238051 माइक्रोकंट्रोलर प्रोग्रामिंग में, किस निर्देश का उपयोग सॉफ्टवेयर टाइमिंग लूप (software timing loop) में समय व्‍यर्थ करने के लिए किया जाता है?
A. NOP
B. CLR A
C. SWAP
D. DA A
Q.24A 2000/200 V transformer absorbs 400 Watts. Find the iron loss current.
A. 2.0 A
B. 5.0 A
C. 0.2 A
D. 0.5 A
Q.25With reference to the AC and DC transmission, state whether the following statements are true/false.

1. In AC transmission, power is proportional to the product of the line end voltages.
2. In DC transmission, power is proportional to the difference of the line end voltages.
A. 1- True, 2 - True
B. 1 - False, 2 - False
C. 1 - True, 2 - False
D. 1 - False, 2 - True
Q.26How many squares will be there in a three variable Karnaugh map?
A. 2
B. 8
C. 16
D. 4
Q.27At the starting of induction motor the rotor frequency is:
A. twice the supply frequency
B. half of the supply frequency
C. same as supply frequency
D. zero
Q.28Intermediate switch is also called the __________.
A. two-way centre-off switch
B. two-way switch
C. four-way switch
D. one-way switch
Q.29Which of the following methods of heating is most suitable for drying of paints?
A. Dielectric heating
B. Electrical resistance heating
C. Infrared heating
D. Induction heating
Q.30The ratio of the luminous flux to the power input is called _______________.
A. beam factor
B. lamp efficiency
C. utilisation factor
D. absorption factor
Q.31Compounding of steam turbine is done for:
A. balancing the turbine
B. reducing the rotor speed
C. increasing the rotor speed
D. reducing the work done
Q.32The set of horizontal and vertical lines permanently marked on the CRT screen is called:
A. aquadag
B. graticule
C. focusing anode
D. control grid
Q.33Which of the following is NOT a valid method of cooling of transformer?
A. Water Natural Oil Forced
B. Oil Forced Water Forced
C. Oil Natural Water Forced
D. Oil Natural Air Forced
Q.34A transformer with magnetic leakage is equivalent to an ideal transformer with:
A. inductive coils in primary and secondary circuits
B. high primary resistance
C. inductive coil in primary circuit
D. inductive coil in secondary circuit
Q.35Which of the following faults is least severe in power systems?
A. L-L-L
B. L-L-G
C. L-G
D. L-L
Q.36To increase the voltage range of an analogue voltmeter an additional resistance is added in series with the meter resistance. This additional resistance is called ________________.
A. multiplier
B. shunt
C. short
D. divider
Q.37Which of the following does NOT help in achieving inherent reliability in protective relay?
A. Good workmanship
B. Low contact pressure
C. Robust construction
D. Dust free enclosures
Q.38Which of the following IC logic families has minimum value of fan-out?
A. ECL
B. CMOS
C. Low power Schottky TTL
D. Standard TTL
Q.39In an organisation, which of the following positions is on the top?
A. Production Manager
B. Sales Manager
C. Managing Director
D. Marketing Manager
Q.40A 4-pole, 3-phase induction motor is supplied through a 50 Hz supply. On full load, its speed is observed to be 1410 RPM. Calculate the full load slip.
A. 2 percent
B. 6 percent
C. 3 percent
D. 4 percent
Q.41Process Field-Bus (PROFI-BUS) is a/an:
A. German standard
B. American standard
C. Asian standard
D. African standard
Q.42स्टेपिंग मोटरों (stepping motors) के उच्च गति पर प्रचालन को __________________ कहा जाता है।
A. फ़ास्ट फॉरवर्ड (fast forward)
B. स्लेविंग (slewing)
C. जॉगिंग (jogging)
D. इंचिंग (inching)
Q.43In Nominal-T configuration of medium transmission line, the shunt capacitance is assumed to be:
A. distributed equally throughout the length
B. concentrated at the middle of the line
C. concentrated at the sending end of the line
D. concentrated at the receiving end of the line
Q.44The basic circuit for the ECL family is the _____________ gate.
A. OR/NOR
B. XNOR
C. NAND
D. AND
Q.45Which of the following is NOT a desirable characteristic of the conductor used for transmission and distribution of electrical energy?
A. High specific gravity
B. Low specific resistance
C. Low cost
D. High tensile strength
Q.46A single input gate in which input and output are same is called _______________.
A. buffer
B. AND
C. inverter
D. EX-NOR
Q.47Which of the following softwares is used for programming of embedded devices?
A. PSCAD
B. Keil uVision
C. ETAP
D. Multisim
Q.48Which of the following is NOT a type of distance relay?
A. Impedance relay
B. Mho relay
C. Reactance relay
D. Buchholz relay
Q.49Which part of the steam power plant converts mechanical energy into electrical energy?
A. Boiler
B. Turbine
C. Furnace
D. Generator
Q.50Which of the following practices can significantly reduce the need of new investment in energy generation or supply?
A. Increase the tariff on energy
B. Energy conservation
C. Load shedding
D. Reduced supply of electricity in specific areas
Q.51The approximate value of surge impedance for overhead lines is:
A. 100 ohms
B. 1500 ohms
C. 1000 ohms
D. 400 ohms
Q.52Which of the following is the ore of aluminium?
A. Chalcopyrite
B. Hematite
C. Cryolite
D. Graphite
Q.53Which of the following materials is NOT used for the filament of incandescent lamp?
A. Tungsten
B. Tantalum
C. Carbon
D. Silver
Q.54Which element of the flowchart is used to begin and end the programs?
A. Rectangle box
B. Bubble
C. Arrow
D. Diamond
Q.55The loss in draught in a chimney is _______________ of the total draught produced by it.
A. 20 percent
B. 10 percent
C. 40 percent
D. 5 percent
Q.56Which of the following motors is most widely used for printers?
A. Stepper motor
B. Synchronous motor
C. DC series motor
D. Induction motor
Q.57For the same power output, which power plant of the following has minimum operating charges?
A. Hydel plant
B. Nuclear plant
C. Gas turbine plant
D. Thermal plant
Q.58What is the minimum requirement of connected load in a new building for the energy conservation building code to be applicable?
A. 100 kW
B. 1000 kW
C. 10 MW
D. 500 kW
Q.59Ladder diagram is associated with _______________.
A. microprocessor
B. PLC
C. SCADA
D. microcontroller
Q.60Constant product characteristics of a directional relay is in the form of ____________.
A. straight line with negative slope
B. rectangular hyperbola
C. square wave
D. straight line with positive slope
Q.61The ripple factor of a power supply is the ratio of:
A. RMS value to peak value
B. peak value to DC value
C. RMS value to DC value
D. peak value to RMS value
Q.62
A. bell
B. hooter
C. loud speaker
D. siren
Q.63Which of the following is a conventional source of energy?
A. Biomass
B. Wind
C. Fossil fuels
D. Solar energy
Q.64Which of the following is a semiconductor material?
A. Bakelite
B. Germanium
C. Asbestos
D. Brass
Q.65Iron-Constantan thermocouple is commercially known as ____________ thermocouple.
A. E-type
B. T-type
C. K-type
D. J-type
Q.66उत्पादन योजना और नियंत्रण प्रणाली में, __________ का अर्थ भविष्य के कार्य के प्रकार, मात्रा और गुणवत्ता का आकलन होता है।
A. पूर्वानुमान (Forecasting)
B. डाटा प्रासेसिंग (data processing)
C. डिस्पैचिंग (dispatching)
D. शिड्यूलिंग (Scheduling)
Q.67
A. fuse
B. heating element
C. relay coil
D. flow switch
Q.68The transmission of instructions from the top executive to the lowest grade executive is called:
A. unofficial communication
B. downward communication
C. horizontal communication
D. upward communication
Q.69Which of the following practices is an example of a medium-term energy conservation scheme?
A. Repairs of system or leakages
B. Minimisation of excess combustion air in furnace
C. Improved housekeeping
D. Improvement and low-cost modifications in existing system
Q.70Which of the following devices has only two terminals?
A. SCR
B. TRIAC
C. DIAC
D. UJT
Q.71Mercury vapour light is always _______________ in colour.
A. bluish
B. yellowish
C. pinkish
D. reddish
Q.72Which of the following methods of welding does NOT require electrode?
A. TIG welding
B. Laser beam welding
C. Resistance welding
D. Plasma arc welding
Q.73In which of the following relays is the generation of gas used as a means of fault detection?
A. Induction cup relay
B. Reactance relay
C. Mho relay
D. Buchholz relay
Q.74Which of the following faults is least likely to occur in power systems?
A. L-L-G
B. L-G
C. L-L-L
D. L-L
Q.75Which of the following is NOT an example of inert gas welding?
A. Thermit welding
B. MAG welding
C. MIG welding
D. TIG welding
Q.76Which of the following wiring systems is most economical for house wiring?
A. Cleat wiring
B. PVC casing and capping wiring
C. Concealed conduit wiring
D. Metal sheathed wiring
Q.77The average current rating of a semiconductor diode will be maximum for:
A. pure dc
B. pure ac
C. half-wave rectified ac
D. full-wave rectified ac
Q.78A relay with 5A rating is having the relay setting of 125 percent. Find the operating current of the relay.
A. 6.25A
B. 10A
C. 5A
D. 3.75A
Q.79Which of the following is an application of induction heating?
A. Room heater
B. Wood gluing
C. Brazing
D. Immersion water heater
Q.80Which of the following statements is INCORRECT for squirrel cage rotor of induction motor?
A. It is also called a short-circuited rotor.
B. Airgap between stator and rotor is not uniform.
C. External resistance cannot be introduced in rotor circuit.
D. Slip ring and brush assembly are not required.
Q.81In 8051 microcontroller, which of the following instructions is an example of unconditional jump?
A. SJMP
B. JNZ
C. CJNE
D. JZ
Q.82Which of the following methods of cleaning is NOT suitable for electrical equipment?
A. Non-conductive sandblasting
B. Brushing
C. Vacuum cleaning
D. Shot blasting
Q.83Which of the following type of material is used to construct variable reluctance motor?
A. Paramagnetic
B. Diamagnetic
C. Non-magnetic
D. Ferromagnetic
Q.84Which of the following is INCORRECT for an ideal transformer?
A. Zero winding resistance
B. Zero leakage flux
C. Zero permeability
D. No losses
Q.85As per classical organisation theory, a supervisor CANNOT directly supervise the work of more than ________ subordinates.
A. 1 to 2
B. 12 to 15
C. 8 to 10
D. 5 to 6
Q.86The board on which the energy meter, cut-out, neutral link are installed is called __________________.
A. main switch board
B. distribution board
C. service board
D. switch board
Q.87Using Boolean algebra, if the following Boolean expression is minimised, then the result will be:

AB + ABC + AB (D+E)
A. ABCD
B. AB
C. ABC
D. A
Q.88निम्न में से किस स्थिति में विद्युत मोटर को बार-बार चालू और बंद करने की आवश्यकता होती है?
A. पेपर मिल
B. लिफ्ट और हॉइस्ट
C. ग्राइंडिंग मिल
D. एयर कंडीशनर
Q.89
A. OR
B. NOT
C. AND
D. EX-OR
Q.90
A. LED
B. Tunnel diode
C. Photo diode
D. Zener diode
Q.91Which of the following functions is NOT under the scope of marketing management?
A. Packaging
B. Advertising
C. Sales promotion
D. Quality control
Q.92Which part of a motor needs maximum attention for maintenance?
A. Rotor winding
B. Stator winding
C. Frame
D. Bearing
Q.93The base of octal number system is _______.
A. 2
B. 8
C. 16
D. 10
Q.94What is the ohms/volt rating of a voltmeter with a 1 mA movement?
A. 10000 Ω/V
B. 10 Ω/V
C. 1000 Ω/V
D. 100 Ω/V
Q.95A power plant has load factor = 0.75 and capacity factor = 0.60. If the maximum demand is 80 MW, then find the plant capacity.
A. 135 MW
B. 90 MW
C. 100 MW
D. 60 MW
Q.96LabVIEW is the abbreviated form of _______________.
A. Laboratory Virtual Instruments Engineering Workbench
B. Laboratory Visual Instrument for Electronic Workbench
C. Laboratory Visual Instrument for Electrical Wiring
D. Laboratory Visual Instrumentation for Engineering Work
Q.97A pressure gauge is calibrated between 100 bar and 350 bar. The scale span is ________________.
A. 250 bar
B. 350 bar
C. 100 bar
D. 450 bar
Q.98In an op-amp, the differential mode gain is __________________.
A. very low
B. always unity
C. always zero
D. very high
Q.99Which of the following materials can serve the purpose of acceptor impurity for obtaining p-type semiconductor?
A. Gallium
B. Arsenic
C. Antimony
D. Phosphorus
Q.100In 8051 microcontroller, the flags are all stored in the _______________.
A. PSW
B. stack pointer
C. program counter
D. accumulator
Q.101Which of the following heating elements is suitable for the highest temperature?
A. Plastic
B. Tungsten
C. Nichrome
D. Silicon carbide
Q.102Which of the following binary code is also called gray code?
A. Excess-3 code
B. Reflected code
C. Biquinary code
D. BCD code
Q.103In a measurement system, which of the following static characteristics is NOT desirable?
A. Sensitivity
B. Drift
C. Linearity
D. Accuracy
Q.104In 8051 assembly language, the execution of which instruction affects the carry flag?
A. RR A
B. SWAP A
C. RL A
D. RRC A
Q.105
A. dependent on base-emitter voltage
B. dependent on collector-emitter voltage
C. always constant
D. dependent on collector current
Q.106Which of the following is NOT a valid type of DC motor?
A. Separately excited motor
B. Squirrel cage motor
C. Series motor
D. Shunt motor
Q.107Permeability can be considered as the:
A. ability to resist the change in magnetisation
B. readiness of a material to accept magnetism
C. ability to oppose the electric current through it
D. ability of the material to allow the magnetic lines to pass through it
Q.108Which of the following is NOT a valid advantage of underground system of electrical distribution as compared to overhead system?
A. Less maintenance
B. Decent appearance
C. Long life
D. Low cost
Q.109The energy conservation building code is applicable to _______________.
A. old buildings only
B. old as well as new buildings
C. new buildings only
D. open lands and farms only
Q.110Which of the following statements is true for Ferranti-effect?
A. Sending end voltage is zero
B. Receiving end voltage is greater than sending end voltage
C. Sending end voltage is greater than receiving end voltage
D. Receiving end voltage is zero
Q.111Which of the following has initiated various promotional provision in support of the EC Act?
A. ECBD
B. BEE
C. BIS
D. Designated consumers
Q.112The signal generated by the time-base circuitry of the CRO is basically a:
A. saw-tooth waveform
B. triangular waveform
C. sinusoidal waveform
D. square waveform
Q.113Which of the following systems is associated with ash handling in thermal power plants?
A. Superheater
B. Condenser
C. Electrostatic precipitator
D. Economiser
Q.114Overhauling is the part of _______________ maintenance.
A. corrective
B. breakdown
C. predictive
D. preventive
Q.115According to Boolean algebra, the resultant of the operation (A + AB) will be __________________.
A. A + B
B. AB
C. B
D. A
Q.116In case of AC transmission at 132 kV using 3-phase single circuit cables, the charging kVA is __________.
A. 3125 kVA
B. 1500 kVA
C. 1250 kVA
D. 9375 kVA
Q.117In which of the organisational conflicts is open aggression observed?
A. Felt conflict
B. Perceived conflict
C. Latent conflict
D. Manifest conflict
Q.118
A. Single-pole switch
B. Multi-position switch
C. Three-pole switch
D. Two-pole switch
Q.119If the shunt admittance of a transmission line is ignored, the torque angle at which maximum power will occur is _______________.
A.
B.
C.
D.
Q.120A 2-input gate gives high output only when both the inputs are low. For all other conditions the output remains low. Identify the gate.
A. EX-OR
B. OR
C. NOR
D. NAND
Q.121Forbidden energy gap is largest in _________.
A. conductor
B. superconductor
C. insulator
D. semiconductor
Q.122Which of the following methods of speed control of induction motor can be only used for wound rotor type induction motor?
A. Stator frequency control
B. Rotor resistance control
C. Stator voltage control
D. Stator voltage and frequency control
Q.123For a single-phase 250/3000 volts, 50 Hz transformer, the EMF per turn is 8 volts. Find the number of secondary turns.
A. 375
B. 325
C. 48
D. 32
Q.124A transformer having 1000 primary turns is connected to a 250 V AC supply. For a secondary voltage of 300 V, the number of secondary turns should be:
A. 800
B. 600
C. 1200
D. 1600
Q.125Donor type impurities have _______________ valence electrons.
A. 2
B. 5
C. 4
D. 3
Q.126Which of the following frequency meters works on the heterodyne principle?
A. Wien bridge frequency meter
B. Digital frequency counter
C. Oscilloscope
D. Zero beat frequency meter
Q.127Which of the following bridges is used for most accurate inductance measurement of inductors having high value of Q-factor?
A. Schering bridge
B. Kelvin bridge
C. Hay bridge
D. Maxwell bridge
Q.128Laws of Electrolysis were formulated by _________.
A. Lord Kelvin
B. Max Planck
C. Alexander Fleming
D. Michael Faraday
Q.129In case of IDMT over current relay, IDMT means:
A. Inverse Differential Minimum Time
B. Inverse Differential Maximum Time
C. Inverse Definite Minimum Time
D. Inverse Definite Maximum Time
Q.130Simulink is the GUI based companion software for _______________.
A. MATLAB
B. ETAP
C. LabVIEW
D. MAGNET
Q.131
A.
B.
C.
D.
Q.132The one major disadvantage of CMOS is __________________.
A. high power dissipation
B. high noise margin
C. high propagation delay
D. low fan-out
Q.133Which of the following is the correct sequence of steps in a coal handling system?
A. Coal delivery, Preparation, Inplant handling, Furnace firing
B. Preparation, Inplant handling, Furnace firing, Coal delivery
C. Inplant handling, Furnace firing, Coal delivery, Preparation
D. Coal delivery, Preparation, Furnace firing, Inplant handling
Q.134Which of the following parts absorbs secondary electrons in CRT?
A. Control grid
B. Cathode
C. Accelerating anode
D. Aquadag coating
Q.135Which of the following is a bidirectional device?
A. PN diode
B. SCR
C. TRIAC
D. GTO
Q.136Total number of 8-bit ports available in Microcontroller 8051 are _______________.
A. 6
B. 8
C. 2
D. 4
Q.137In common collector configuration of transistor, the voltage gain is always:
A. greater than unity
B. less than unity
C. zero
D. infinity
Q.138एनालॉग मीटर (analogue meter) उपयोग करते समय, कौन सी त्रुटि हो सकती है, यदि दृष्टि-रेखा (line of sight) मापक स्केल (measuring scale) के ठीक लंबवत नहीं है?
A. स्केल त्रुटि (Scale error)
B. भारण त्रुटि (Loading error)
C. घर्षण त्रुटि (Friction error)
D. लंबन त्रुटि (Parallax error)
Q.139A temperature reading is recorded as 25.70°C. The number of significant figures in the reading is ______________.
A. 4
B. 5
C. 3
D. 2
Q.140Which of the following semiconductor devices can be used in enhanced mode?
A. JFET
B. UJT
C. NPN transistor
D. MOSFET
Q.141Which of the following is NOT a correct way of energy conservation?
A. Effective periodic maintenance
B. Increase reactive loads
C. Improving power factor
D. Replace electrical circuit with solid state circuit
Q.142For a 4-pole simplex wave-wound DC generator, number of parallel paths will be __________________.
A. 2
B. 8
C. 1
D. 4
Q.143The T flip-flop is a single-input version of the __________________ flip-flop.
A. JK
B. D
C. RS
D. clocked RS
Q.144Natural draught is produced by _______________.
A. exhaust fan
B. chimney
C. steam jet
D. fan
Q.145Which of the following insulating materials offers maximum working temperature?
A. Class A
B. Class B
C. Class H
D. Class F
Q.146For transformers above 1000 KVA rating, inspection of Buchholz relay is carried out:
A. every 3 years
B. every 4 years
C. every year
D. every 2 years
Q.147A stepper motor has a step angle of 3°. Determine the number of steps required for the shaft to make 25 revolutions.
A. 300
B. 600
C. 3000
D. 6000
Q.148In a three-phase induction motor, the maximum torque is independent of:
A. rotor reactance
B. rotor resistance
C. synchronous speed
D. applied voltage
Q.149Which of the following is NOT a discharge lamp?
A. Neon lamp
B. Sodium vapour lamp
C. Incandescent lamp
D. Mercury iodide lamp
Q.150Compounds which are chemically identical but differ in their physical properties are called _______.
A. allotropes
B. polymers
C. isotopes
D. isomers
Q.1______ नृत्य हरियाणा में केवल महिलाओं द्वारा शादियों और त्योहारों में किया जाता है।
A. फाग (Phag)
B. खोरिया (Khoria)
C. झूमर (Jhumar)
D. धमाल (Dhamal)
Q.2भारतीय संविधान के अनुच्छेद 22(2) के अनुसार, किसी व्यक्ति को मजिस्ट्रेट की अनुमति के बिना ____________ से अधिक समय तक हिरासत में नहीं रखा जा सकता है।
A. 36 घंटे
B. 12 घंटे
C. 48 घंटे
D. 24 घंटे
Q.3दिसंबर 2020 में हुआ 'द ग्रेट कॉनजंक्शन' एक खगोलीय घटना थी, जिसमें __________ ग्रह शामिल थे।
A. मंगल और बृहस्पति
B. बृहस्पति और शनि
C. शनि और बुध
D. शुक्र और मंगल
Q.4निम्न में से कौन-सा कथन गलत है?
A. बृहत ज्वार, एक महीने में दो बार आता है, पहला पूर्णिमा के दौरान और दूसरा अमावस्या के दौरान।
B. ज्वार की ऊंचाई तब अधिक होती है जब सूर्य, चंद्रमा और पृथ्वी सीधी रेखा में होते हैं।
C. उच्च ज्वार और निम्न ज्वार के बीच का समय, जब पानी का स्तर गिर रहा होता है, उसे 'एब' (the ebb) कहा जाता है।
D. सामान्यतः, बृहत ज्वार और लघु ज्वार के बीच 15 दिन का अंतराल होता है।
Q.5_____ ने लखनऊ संधि में महत्वपूर्ण भूमिका निभाई थी और 1934 के बाद मुस्लिम लीग का पुनर्गठन किया था।
A. मोहम्मद अली जिन्ना
B. डॉ. जाकिर हुसैन
C. मौलाना अबुल कलाम आज़ाद
D. खान अब्दुल गफ्फार खान
Q.6बांग्लादेश, पाकिस्तान और _____________ के कुछ समुदायों के शरणार्थी, नागरिकता (संशोधन) विधेयक, 2019 के अंतर्गत भारतीय नागरिकता के लिए पात्र हैं।
A. नेपाल
B. म्यांमार
C. भूटान
D. अफ़ग़ानिस्तान
Q.7The Border–Gavaskar Trophy is a Test cricket series played between India and _____.
A. New Zealand
B. England
C. Australia
D. West Indies
Q.8निम्न में से कौन-सा त्योहार हिंदू श्रावण (श्रवण) महीने के पांचवें दिन मनाया जाता है, जिसमें धार्मिक-क्रिया/पूजा-पाठ के दौरान दूध चढ़ाया जाता है?
A. जीवती पूजा
B. नाग पंचमी
C. वसंत (बसंत) पंचमी
D. गंगा दशहरा
Q.9भारतीय रिज़र्व बैंक द्वारा 2016 में महात्मा गांधी (नई) श्रृंखला के भाग के रूप में जारी किए गए ₹______ मूल्यवर्ग में नए डिज़ाइन किए गए बैंक नोटों का आधार रंग (base colour) मैजेंटा (गहरा गुलाबी) है।
A. 500
B. 2000
C. 100
D. 200
Q.10_____________, को मुस्लिम लीग ने 'डायरेक्ट एक्शन डे (सीधी कार्यवाही दिवस)' घोषित किया था।
A. 15 दिसंबर 1946
B. 17 सितंबर 1944
C. 16 अगस्त 1946
D. 18 नवंबर 1944
Q.11निम्न में से कौन-सा कथन गलत है?
A. जीवाश्म ईंधन के दहन से वायु में निलंबित कणों की मात्रा बढ़ जाती है।
B. धुंध (Smog), वायु प्रदूषण का प्रत्यक्ष संकेत है।
C. वायु में हानिकारक पदार्थों की सामग्री में वृद्धि को वायु प्रदूषण कहा जाता है।
D. वायु प्रदूषण से हेपेटाइटिस, हैजा और टाइफाइड जैसी बीमारियां होती हैं।
Q.12सामान्यतः भोजन में उपयोग किया जाने वाला नमक, ______________ अम्ल और सोडियम हाइड्रॉक्साइड विलयन के संयोजन से बनाया जा सकता है।
A. सल्फ्यूरिक
B. नाइट्रिक
C. हाइड्रोक्लोरिक
D. क्लोरिक
Q.13____________, संघ ‘सिलेंट्रेटा’ (Coelenterata’) ‘निडेरिया’ (‘Cnidaria’) से संबंधित होते हैं।
A. मच्छर (Mosquitoes)
B. फीता कृमि (Tapeworms)
C. मूँगा (Corals)
D. टिड्डी (Locust)
Q.14दिसंबर 2020 में, अखिल भारतीय फुटबॉल महासंघ (All India Football Federation) ने औपचारिक रूप से, ए.एफ.सी. (AFC) एशियाई कप ____________ आयोजित करने की अपनी उम्मीदवारी की घोषणा की है।
A. 2023
B. 2027
C. 2029
D. 2025
Q.15The _____ is the western-most of the Himalayan rivers in India.
A. Brahmaputra
B. Indus
C. Sutlej
D. Ganga
Q.16India ranks _____ in the Human Development Index released by the United Nations in December 2020.
A. 130th
B. 138th
C. 137th
D. 131st
Q.17In November 2020, Joe Biden was elected as the _____ President of the US.
A. 47th
B. 43rd
C. 44th
D. 46th
Q.18शरत कमल, भारत के पेशेवर ___________ खिलाड़ी हैं।
A. स्क्वाश
B. लॉन टेनिस
C. टेबल टेनिस
D. बैडमिंटन
Q.19भारत में बैंकिंग के संदर्भ में निम्न में से कौन-सा कथन सही नहीं है?
A. भारतीय रिजर्व बैंक द्वारा मुद्रा नोट जारी किए जाते हैं।
B. बचत खाते वाली शेष राशि को 'डिमांड डिपॉजिट' कहा जाता है।
C. भारत सरकार द्वारा सिक्के जारी किए जाते हैं।
D. चालू खातों में शेष राशि को ‘टाइम डिपॉजिट' कहा जाता है।
Q.20मदुरै मीनाक्षी अम्मन मंदिर में ________ त्योहार, देवी मीनाक्षी का भगवान सुंदरेश्वर के साथ दिव्य विवाह के उत्सव रूप में मनाया जाता है।
A. मासी (Masi)
B. पुरात्तासी सनी (Purattasi Sani)
C. चिथिराई (Chithirai)
D. वैकासी विसकम (Vaikasi Visakam)
Q.1तीन मित्रों रिया, पंकज और गौरव की वर्तमान आयु का अनुपात क्रमश: 3 : 4 : 5 है। पांच वर्ष पहले उनकी आयु का योग 69 था। पंकज की वर्तमान आयु ज्ञात कीजिए।
A. 28 वर्ष
B. 21 वर्ष
C. 32 वर्ष
D. 35 वर्ष
Q.2यदि '–' का अर्थ '×' है, '×' का अर्थ '+' है, '+' का अर्थ '÷' है, और '÷' का अर्थ '–' है, तो निम्‍न व्‍यंजक का मान ज्ञात कीजिए।

335 + 67 – 8 ÷ 21 × 9
A. 169
B. 28
C. 52
D. 231
Q.3Two different positions of the same dice marked with the letters G, H, I, J, K and L are shown. This dice is formed by folding which of the following option figures?
A.
B.
C.
D.
Q.4Select the Venn diagram that best represents the relationship between the following classes.

Outdoor Games, Cricket, Chess, Hockey
A.
B.
C.
D.
Q.5Identify the number that does NOT belong to the following series.

7, 21, 63, 199, 567, 1701
A. 63
B. 567
C. 21
D. 199
Q.6Select the option that is true regarding the following two statements labelled Assertion (A) and Reason (R). Assertion (A): Wearing masks helps in controlling the spread of COVID-19 virus. Reason (R): Masks repel coronavirus.
A. Both 'A' and 'R' are true and 'R' is the correct explanation of 'A'.
B. A' is true but 'R' is false.
C. Both 'A' and 'R' are true but 'R' is not the correct explanation of 'A'.
D. A' is false but 'R' is true.
Q.7Study the diagram carefully and answer the question that follows.
The given diagram shows the number of students in a school who are practicing different dance forms.

What is the number of students who practice both Odissi and Kuchipudi, but NOT Kathak?
A. 50
B. 9
C. 30
D. 14
Q.8Select the option that is related to the third number in the same way as the second number is related to the first number.

253 : 320 :: 323 : ? 
A. 365
B. 342
C. 400
D. 390
Q.9एक पासे की दो अलग-अलग स्थितियां दर्शाई गई हैं जिस पर अक्षर a, b, c, d, e और f दिख रहे हैं। निम्‍न विकल्‍पों में से, इस पासे का अन्‍य कौन सा विन्‍यास संभव है?
A.
B.
C.
D.
Q.10Identify the number that does NOT belong to the following series.

256, 289, 324, 361, 420, 441, 484
A. 420
B. 441
C. 324
D. 361
Q.11दिए गए कथनों और निष्‍कर्षों को ध्‍यानपूर्वक पढ़ें। यह मानते हुए कि कथनों में दी गई जानकारी सत्‍य है, भले ही वह सामान्‍य रूप से ज्ञात तथ्‍यों से भिन्‍न प्रतीत होती हो, निर्धारित कीजिए कि दिए गए निष्‍कर्षों में से कौन से निष्‍कर्ष कथनों का तार्किक रूप से अनुसरण करते है/हैं।
कथन: λ ≤ Ω, λ > £, π ≥ ф, £ >π
निष्‍कर्ष :
I. Ω > ф
II. λ ≤ π
A. केवल निष्‍कर्ष II अनुसरण करता है
B. निष्‍कर्ष I और II दोनों अनुसरण करते हैं
C. केवल निष्‍कर्ष I अनुसरण करता है
D. निष्‍कर्ष I और II में से कोई एक अनुसरण करता है
Q.12तान्‍या की वर्तमान आयु, मोहित की वर्तमान आयु से दोगुनी है। पांच वर्ष पहले, मोहित की आयु, तान्‍या की आयु की एक-तिहाई थी। मोहित की वर्तमान आयु ज्ञात कीजिए।
A. 20 वर्ष
B. 25 वर्ष
C. 10 वर्ष
D. 15 वर्ष
Q.13Select the option that can replace the question mark (?) in the following number series.

19, 28, ?, 52, 67
A. 39
B. 34
C. 36
D. 43
Q.14Select the option that can replace the question mark (?) in the following number series.

16, 48, 24, 72, 36, ?
A. 108
B. 92
C. 88
D. 120
Q.15Read the given statements and conclusions carefully. Assuming that the information given in the statements is true, decide which of the conclusions logically follows from the statements.

Statements: P ≥ R, R > T, T ≤ A

Conclusions:
I. P > A
II. T < P
A. Only conclusion I follows.
B. Only conclusion II follows.
C. Either conclusion I or II follows.
D. Neither conclusion I nor II follows.
Q.16Which two numbers should be interchanged in the given equation so that the equation becomes correct?

96 ÷ 8 + 7 – 2 × 3 = 23
A. 8 and 3
B. 2 and 3
C. 7 and 2
D. 3 and 7
Q.17Select the option that can replace the question mark (?) in the following number series.

53, 90, 127, 164, ?
A. 260
B. 201
C. 221
D. 182
Q.18Study the given pattern carefully and select the number that can replace the question mark (?) in it.
A. 175
B. 160
C. 190
D. 205
Q.19Select the Venn diagram that best represents the relationship between the following classes.

Universe, Earth, India, Gujarat, Bhilai
A.
B.
C.
D.
Q.20निम्‍न आरेख में, त्रिभुज पुरुषों को निरूपित करता है, वृत्‍त बेरोजगारों को निरूपित करता है, आयत ग्रामीणों को निरूपित करता है तथा वर्ग नर्तकों को निरूपित करता है।

कितने पुरुष ऐसे हैं जो न तो बेरोजगार हैं और न ही नर्तक हैं?
A. 9
B. 26
C. 12
D. 17
Q.1कौन' सर्वनाम का परिमाणवाचक विशेषण होगा-
A. किस
B. कितना
C. कैसा
D. किसका
Q.2हिन्दी में कुल कितने सर्वनाम हैं?
A. 13
B. 9
C. 11
D. 15
Q.3चुप्पा बहुत चालाक होता है।' अर्थ को व्यांजित करने वाली उपयुक्त लोकोक्ति कौन सी है?
A. भूख लगे तो घर की सूझी
B. बहरा सो गहरा
C. फिसल पड़े तो हर गंगा
D. प्यासा कुएँ के पास जाता है
Q.4पगड़ी' किस प्रकार का शब्द है?
A. देशज
B. तद्भव
C. तत्सम
D. विदेशी
Q.5सीता जा रही थी।' वाक्य का काल है -
A. पूर्ण भूत
B. सामान्य भूत
C. संधिग्ध भूत
D. अपूर्ण भूत
Q.6चिड़िया' किस प्रकार का शब्द है?
A. तद्भव
B. विदेशी
C. देशज
D. तत्सम
Q.7मानव पढ़ रहा है।' वाक्य का काल है -
A. पूर्ण वर्तमान
B. सामान्य वर्तमान
C. तात्कालिक वर्तमान
D. संदिग्ध वर्तमान
Q.8सदा प्रसन्न रहो।' वाक्य में क्रिया की वृत्ति है-
A. संदेहसूचक
B. आज्ञापूरक
C. संकेतसूचक
D. इच्छासूचक
Q.9विधान सभा का चुनाव एक निश्चित ___________ के लिए होता है। रिक्त स्थान के लिए सर्वाधिक उपयुक्त शब्द कौन सा है?
A. क्षण
B. काल
C. युग
D. अवधि
Q.10पपीहा ___________ करता है। रिक्त स्थान के लिए उपयुक्त शब्द कौन सा है?
A. पिया - पिया
B. काँव - काँव
C. पीउ - पीउ
D. कू - कू
Sections

Questions
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200



 
Answered
 
UnAnswered
 
Review-Later (RL)
 
Not-visited